OKX Wallet download

List of contents in this article:

• 1, What is the correct way to ignite a car?
• 2、 How to start the car ignition button?
• 3,Correct operation of car ignition

What is the correct way to ignite a car?

1. First, turn on the left turn signal and observe the road conditions to ensure safety. Start the car, step on the clutch, put into the first gear, release the brake, step on the accelerator with your right foot, start the car, continue to step on the accelerator, and accelerate and upshift. How to drive a car correctly? Look at the car before you get on the car. Before getting on the car, go around the car to check the bottom of the car, tires and bottom of the car for oil leakage.

2. After the key is inserted into the ignition switch, it stays in each gear for about 1 or 2 seconds. At this time, you can hear the sound of the electrical equipment being energized, and then enter the next gear.Some cars can go directly to the ON position, and then wait for all aspects of the electrical appliances to start in all directions for about 6-7 seconds, and then turn the key to the START state to ignit directly.

3. Start the engine in the order of starting operation on the flat road, and check whether the second operation of each instrument is normal. Step on the clutch pedal and hang the gearshift lever into the low gear. Turn on the left turn signal, honk the horn, and observe the front, left, right, top and rearview mirrors of the vehicle to see if there are any obstacles that hinder the automatic start. Be sure to pay attention to safety when starting.

4. The method of igniting the car in extremely cold weather is as follows: 1 Check the battery. There is a button battery-sized inspection window to indicate the battery status. If it is green, it means that the battery power is more than 50%. You can rest assured to try to ignite it once or twice. 2 If you raise the engine temperature, you can light the stove and bake it under the engine. Engine 3 increases the ignition probability 4.

How to start the car ignition button?

1. START gear: start gear. When the key is stwewed to this position, the starter circuit will be turned on, which will drive the engine to run and start. After releasing, the key will automatically return to ON gear. And the START gear is the engine start-up gear, which will automatically return to the normal state after starting, that is, the ON gear.

2. The way to use the car ignition device is to start the vehicle when the driver steps on the brake and leaves the contract and uses the car key to turn the ignition switch to the start gear; the way to use the ignition device of the automatic transmission vehicle is to start the driver to step on the brake to the end and press the ignition switch to start.

3. The three steps of the car ignition switch are as follows: start the vehicle. If it is a key-stwing model, stwing the key to start, and if it is a one-button start-up model, press the one-button start button.

4. After the key is inserted into the ignition switch, stay in each gear for about 1 or 2 seconds. At this time, you can hear the sound of electrified electrical equipment. At the same time, when the oil pump establishes the oil pressure, there will be a slight wheeping sound, or our sound. Wait for the sound to disappear, or after 10 seconds, then enter the next gear, pause and drive.

Correct operation of car ignition

Do not twist the key in the Lock position, wait for about 2 seconds, and then twist the key directly through the ACC position to stop in the ON position and wait for about 5 seconds.

When the car is igniting, you should step on the clutch and step on the brake. Stepping on the clutch can reduce the load of the engine, which is very important, because the clutch is the switch that cuts off the engine and gearbox. If you don't step on the clutch at this time, you will greatly avoid the situation of stepping on the accelerator when it is on fire. If it is a neutral gear , then step on the clutch when you are on fire.

The correct way to ignite a car is to step on the clutch deeply, turn the ignition key to the ON position, wait for 5 to 8 seconds, and then turn the key to the starting position to start the engine;Once the engine starts smoothly, the ignition key should be released immediately to let it automatically return to the ON position.

Before igniting the vehicle, first make sure that the key is in the correct position. If the key is inserted to start, insert the key into the hole first. If it is a one-button start, put the key in the appropriate position in the car. Then check that the gear of the vehicle is in the correct gear, generally P gear and N gear. The engine cannot be started in D gear or R gear.